Rod seal manufacturer in China: A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the “wet end” of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly. See more information on scraper seals.
The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film.
It adopts the most ideal design and improved sealing performance and can minimize the high strength of local stress. This type of seal is designed to simplify installation and reduce particle generation. Moreover, it can be quickly and easily installed and removed to facilitate hardware assembly. It perfectly combines a custom seal design, proprietary bonding technology, and excellent plasma resistance developed for semiconductor applications. And its unique structure can minimize common installation problems.
The rod seals can be operated with or without lubrication. We guarantee strong dimensional stability and a low coefficient of friction. Changes in temperature do not affect its performance. It is easy to install and can be used with piston rods with the larger diameter and heavy-duty hydraulic rod sealing systems to provide a tight and excellent seal. DMS Seals with 12+ years of experience for manufacturing rod seals, we are confident to provide top quality & satisfying product. There are hydraulic rod seals, piston rod seals, etc for selection, welcome to contact us for further details.
Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.
Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. Read more info at dmsseals.com.
DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.
Construction machinery sealing system requirements: High and low temperature resistance Because of continuous work for a long time, if it is outdoors in summer, the hydraulic oil temperature of the machine may exceed 100°C, which requires the seal to be resistant to high temperature. If it is outdoors in winter, the temperature may be around -40°C when it is just turned on, and the seals are required to be resistant to low temperatures. Therefore, the sealing system is required to withstand a wide temperature range. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small.
The O-ring seal, which is also called shaft seal, is noted for a reasonable compression and stretch rate to achieve a good sealing effect. It will not leak when it is sealed statically. At the same time, the O-ring size is properly matched to the groove size. The structure is simple and its installation is very close to the machine. Its most prominent advantage is its self-sealing effect, eliminating the need for periodic adjustments. We guarantee that the size and mounting grooves of all our O-rings are standardized, so they are cost-effective and easy to maintain. They have low frictional resistance and are suitable for occasions where the pressure is often alternating.